AAMCOR is an original equipment manufacturer (OEM), as well as an equipment broker for both new and used mining equipment, and imports and exports to all parts of the world.

Drills and drill equipment

AAMCOR supplies a large range of drills and drill equipment to the mining industry, including air track, core, deep-hole, reverse circulation, track rotary blasthole and rubber-type rotary blasthole drills. We also offer drill parts and assemblies.

Air track drills

We sell Tamrock Bob Track CHA 800’s two units as a pair. They have new clutches, gear boxes, spare parts, and oil analysis on both engines, which have been replaced with factory rebuilds.

Gas, oil and water drills

AAMCOR supplies the Ingersoll Rand T4W water well drill. Manufactured in 1975, the drill includes features such as 12V71 Detroit deck engine, 3209 CAT drive engine, 13-speed transmission, and much more.

AAMCOR is an original equipment manufacturer for both new and used mining equipment.

We supply a large range of drills and drill equipment to the mining industry.

Our drill part rigs are in very good condition and a discount is offered if all the pieces are purchased at the same time.

We can offer training to new owners and crew of the RC drilling system if required.

We also supply the Red B61 water drill. Features of this drill include four winches, near-new engines up and down and 36ft mast. For more specifications please visit our website.

Core drills for the mining industry

We have an extensive variety of core drills for the mining industry, including:

• Longyear HC44 core drill rig
• Ingersol Rand longhole drill
• Longyear LF-70 core drill
• Longyear LF-70 core drill
• CS-1500 core drills
• DMW 45 core drill
• Ingersol Rand TH100
• Longyear diamond drill
• Atlas Copco Mustang A-50 track drill (Geotech drill rig)
• JKS Winkie core drill

Deep-hole drills

Amongst its many other features, the Ingersol Rand RD20 deep-hole drill has a 3412E Caterpillar diesel deck engine, IR compressor, HR 2.5 1250 CFM / 350 PSI and a seven-pod carousel.

Our RD20 Atlas Copco drill has a three-cylinder Caterpillar water injection system, dual motor spurgear head and comes with 3,500ft of used drill steel and a substructure.

We also provide the 2001 Ingersoll Rand drill rig, IR RD 20 Range III deep-hole rig and Scramm T-130 deep-hole rig.

Drill rig parts and assemblies

AAMCOR currently has the following parts available for a DM45E drill rig:

• DM45E 30ft Derrick (complete minus the power-head and carousel)
• Two-motor spur head, low usage since rebuilt
• 30ft carousel

All pieces are in very good condition and a discount is offered if all the pieces are purchased at the same time.

Reverse circulation drills

Our reverse circulation drills include the Ingersol Rand longhole drill, Foremost RC drill, Ingersol Rand TH100 and Chicago pneumatic 700 track rig.

We can offer training to new owners and crew of the RC drilling system if required.

Track rotary blast-hole drills

We offer a number of track rotary blast-hole drills, including the 2004 Tamrock Pantera 1500 with 6075 engine hours and 2454 hammer hours, and the loaded and ready-to-drill Titan 600.

AAMCOR also offer the1991 Driltech C25K4H, DM30, DM45E rotary blast-hole drill, Atlas Copco ROC F-9, IR ECM470 and Ingersoll Rand DM50.

Rubber-type rotary blast-hole drills

AAMCOR is able to offer a range of rubber-type rotary blast-hole drills, including:

• IR T4BH
• 2000 IR RD20
• B-61 mobile drill rig
• TH-55 RC drill
• Schramm T-64 HB
• Schramm T-64
• Mobile B-61 HD
• Bucyrus Erie drill rig
• Schramm T-64 rotary drill rig
• CP650 rotary drill
• Ingersoll Rand T4BH